The complex material engineering of NASA's Webb telescope sunshield
30 June 2016
The material of the sunshield that will fly aboard NASA's James Webb Space Telescope is a complex and innovative feat of material science and engineering.
Each layer is made from a unique composite material, each has a specific thickness and size, and they must be precisely separated in space. There are even special seams and reinforcements to limit meteorite damage.
NASA and its industry partners developed a lightweight, robust way to protect the telescope and mirrors from the sun’s infrared radiation in the material that makes up the sunshield. Some of the things that make the sunshield unique are its strong yet ultra-thin material, special kite-like shape, and the special role of its layers.
The sunshield consists of five layers of a material called Kapton. Each layer is coated with aluminium, while sun-facing side of the two hottest layers (designated Layer 1 and Layer 2) also have a "doped-silicon" (or treated silicon) coating to reflect the sun's heat back into space. The sunshield is a critical part of the Webb telescope because the infrared cameras and instruments aboard must be kept very cold and out of the sun's heat and light to function properly.
Kapton is a polyimide film that was developed by DuPont in the late 1960s. It has high heat-resistance and remains stable across a wide range of temperatures from -269 to +400°C. It does not melt or burn at the highest of these temperatures. On Earth, Kapton polyimide film can be used in a variety of electrical and electronic insulation applications.
The sunshield layers are also coated with aluminium and doped-silicon for their optical properties and longevity in the space environment. Doping is a process where a small amount of another material is mixed in during the Silicon coating process so that the coating is electrically conductive. The coating needs to be electrically conductive so that the Membranes can be electrically grounded to the rest of JWST and will not build up a static electric charge across their surface. Silicon has a high emissivity, which means it emits the most heat and light and acts to block the sun’s heat from reaching the infrared instruments that will be located underneath it. The highly-reflective aluminium surfaces also bounce the remaining energy out of the gaps at the sunshield layer's edges.
Kite-like shape and layers
The kite-like shape and the number of layers of sunshield both play an important role on the Webb telescope. Each of the different layers are positioned and separated with precision to accomplish their function.
"The shape and design also direct heat out the sides, around the perimeter, between the layers," said James Cooper, Webb telescope Sunshield Manager at NASA's Goddard Space Flight Centre, Greenbelt, Maryland. "Heat generated by the Spacecraft bus at the “core,” or centre, is forced out between the membrane layers so that it cannot heat up the optics."
"The five layers are needed to block and re-direct enough heat to get the telescope down to required temperatures, with margin," Cooper said. "The fifth layer is mostly for margin against imperfections, micro-meteoroids holes, etc." The gap between the layers provides an additional insulating effect.
Each layer of the sunshield is incredibly thin. Layer 1 will face the sun and is only 0.05mm (0.002in) thick, while the other four layers are 0.025mm (0.001in). The thickness of the aluminium and silicon coatings are even smaller. The silicon coating is ~50 nanometres (nm) (1.9 microinches) thick, while the aluminium coating is ~100nm (3.93 microinches) thick.
The layers are slightly different sizes and different shapes. Layer 5 (just under the primary mirror) is smallest and Layer 1 is largest. Layer 1 is relatively flat and layer 5 is more curved. The layers are closer together at centre and further apart at the edges to direct heat from the centre to the outside of the layers.
The Webb telescope optics (like the infrared camera and mirrors) must always be protected from direct exposure to any hot objects. So the membranes are sized and positioned such that the mirrors only have a direct line of sight to the cold layer 5, while the sun only directly shines on layer 1 no matter which way the observatory is pointed.
The membrane material is tough, but if it gets a small tear or hole, the hole could become much larger. So, there is a special process called a Thermal Spot Bond (TSB) – areas where each layer is melted together. In addition, reinforcing strips of membrane material are Thermal Spot Bonded to the parent membrane about every 6 feet or so, forming a grid pattern of "rip-stops."
"This has been shown through testing to arrest a tear and keep it from extending outside of a given grid area," said Cooper. So, if a hole occurs in a layer of the sunshield from a meteoroid, or small meteor, the size of the damage is limited. These are not intended to stop a meteoroid, but rather to contain the area of damage.
Extreme temperatures and the sunshield
The material of the sunshield does shrink as it gets colder, and the hot layers expand. Cooper said, "The Kapton variety minimises this compared to some other material choices. We have tested the material so we know how much it shrinks. We account for this in both our manufacturing and in our analysis predictions of the shape we will get in space. We have also tested a one-third-scale five-layer sunshield at temperature and vacuum to verify our predictions."
The James Webb Space Telescope is the scientific successor to NASA's Hubble Space Telescope. It will be the most powerful space telescope ever built. Webb is an international project led by NASA with its partners, the European Space Agency and the Canadian Space Agency.
For more information about the James Webb Space Telescope, visit: www.nasa.gov/webb or jwst.nasa.gov
For more information and images about the sunshield, visit: jwst.nasa.gov/sunshield.html
Video courtesy of NASA/STscl.